Log #52 · Oct 8, 2026
Why Is My Servo Jittering? Causes and Fixes
The real reasons hobby servos twitch, buzz or reset an Arduino, from weak power and missing grounds to library conflicts, with a step-by-step checklist to fix each one.
You wire an SG90 or MG996R servo, upload a sketch, and instead of moving smoothly to its position it twitches, buzzes, shakes in place or makes the whole Arduino reset. Servo jitter is one of the most common beginner problems, and almost always it has one of a handful of causes. This guide goes through them in order of likelihood, with a fix for each.
How a servo decides where to go
A hobby servo reads a pulse every 20 ms. The pulse width, roughly 1 ms to 2 ms, sets the target angle. Inside, a potentiometer measures the actual shaft angle and a small control circuit drives the motor until the two match.
Anything that disturbs the pulse, the supply voltage or the feedback makes the controller think the shaft is in the wrong place, so it corrects, overshoots and corrects again. That back-and-forth is the jitter you see. The basics of wiring and code are in how to control a servo with Arduino.
1. Not enough power (the usual suspect)
An SG90 draws around 100–250 mA while moving and can spike to over 600 mA when it starts or stalls. An MG996R can pull more than 1 A. The Arduino's 5 V pin, especially on USB power, cannot supply that. The voltage dips, the servo's electronics misbehave and sometimes the Arduino resets.
Fix:
- Power servos from a separate 5–6 V supply that can deliver at least 1 A per small servo or 2–3 A per large one: a 4×AA battery pack, a 5 V USB power bank, or a 5 V/6 V adapter or BEC.
- Connect the supply's ground to the Arduino's GND. Without a shared ground the signal has no reference.
- Put a 470–1000 µF electrolytic capacitor across the servo supply, close to the servos. It covers the current spikes when they start moving. See choosing capacitors for polarity and voltage rating.
Do not power servos from the Arduino's VIN pin either. More on safe power paths in how to power an Arduino project.
2. Missing or bad ground
If the servo is powered separately but the grounds are not connected, the signal "floats" relative to the servo and positions wander randomly. Loose breadboard contacts cause the same thing intermittently. Use short, solid connections for the ground and power wires; thin jumper wires add resistance that matters at these currents.
3. Asking for an angle the servo can't reach
Many cheap servos cannot physically reach the full 0° or 180° the library allows. At the ends they push against the internal stop and buzz constantly. Test the real range:
#include <Servo.h>
Servo s;
void setup() {
Serial.begin(9600);
s.attach(9);
}
void loop() {
if (Serial.available()) {
int us = Serial.parseInt(); // type e.g. 600, 1500, 2300
if (us >= 500 && us <= 2500) {
s.writeMicroseconds(us);
Serial.println(us);
}
}
}
Find the values where the servo stops moving without buzzing, then use them in s.attach(9, minUs, maxUs) so write(0) and write(180) stay inside the safe range.
4. Noisy input values
If the angle comes from a potentiometer, joystick or sensor, small fluctuations in the reading make the servo chase tiny changes. Only move the servo when the value changes by more than a couple of degrees:
int lastAngle = -1;
void loop() {
int angle = map(analogRead(A0), 0, 1023, 0, 180);
if (abs(angle - lastAngle) > 2) { // deadband
s.write(angle);
lastAngle = angle;
}
}
Averaging the readings first helps too; see reading a potentiometer and a joystick.
5. Library and interrupt conflicts
The Servo library generates its pulses with a hardware timer and interrupts. Libraries that turn interrupts off for a moment, notably NeoPixel/WS2812 LED libraries and SoftwareSerial at high baud rates, can stretch a pulse and make the servo twitch every time they run.
Fix: use a dedicated servo driver such as the PCA9685 (16 channels over I²C, generates pulses in hardware), or move the conflicting function to hardware serial. On the Uno, the Servo library also takes over Timer1, which disables analogWrite() on pins 9 and 10.
6. The servo is holding a load
A servo holding an arm against gravity constantly corrects tiny errors, which shows up as a faint buzz and small shakes. This is normal, but a cheap servo with a worn potentiometer makes it much worse.
Fixes: reduce the load or use a stronger servo (check the torque math in the robot arm guide), or call s.detach() when the arm does not need to hold position, which stops the pulses and lets the motor rest.
Quick checklist
- Servo on its own 5–6 V supply, not the Arduino's 5 V pin?
- Grounds connected between supply and Arduino?
- 470–1000 µF capacitor across the servo supply?
- Angles inside the servo's real range?
- Deadband or smoothing on noisy inputs?
- No NeoPixel or SoftwareSerial conflicts?
If all six are fine and one servo still jitters while others don't, the servo itself is probably worn. Swap it out; cheap servos are consumables.
— TheSolderBench · found a mistake? tell me