TheSolderBenchnotes from my electronics bench

Log #62 · Oct 11, 2026

How to Choose Motors for a Mobile Robot (Torque and Speed Math)

A simple, step-by-step method to size the drive motors of a wheeled robot from its weight, wheel size, top speed and the slopes it must climb, with a fully worked example.

Robotics · 4 min read · Intermediate

Pick motors that are too weak and your robot crawls, stalls on a rug or can't climb a ramp. Pick motors that are too strong and you waste money, weight and battery. You don't need a simulation to get it right: four numbers about your robot and a few lines of math give you the torque and speed to look for.

What you need to know first

  1. Total mass (m) of the finished robot, including batteries. Guess high.
  2. Wheel radius (r), in meters. A 65 mm wheel has r = 0.0325 m.
  3. Top speed (v) you want, in m/s. 0.3–0.5 m/s is a brisk walk for a small robot.
  4. Steepest slope (θ) it must climb, and how quickly it should accelerate (a).

And the number of driven wheels (N), usually 2 for a differential drive robot.

Diagram of a wheeled robot on a ramp: gravity pulls it down the slope, rolling resistance acts against motion, and the wheel torque equals the total force times the wheel radius
The wheels must push against gravity on the slope, rolling resistance and the force needed to accelerate.

Step 1: force on the wheels

F = m × (g × sin θ + Crr × g × cos θ + a)

  • g × sin θ: the slope pulling you back. On flat ground it's 0.
  • Crr × g × cos θ: rolling resistance. Crr is about 0.01–0.02 for hard wheels on a smooth floor and 0.03–0.05 for rubber wheels on carpet. Use 0.03 if unsure.
  • a: acceleration. 0.5 m/s² reaches 0.5 m/s in one second, which feels responsive.

Step 2: torque per motor

Torque per motor = F × r ÷ N

This is in newton-meters (N·m). Motor sellers often use kg·cm: 1 N·m ≈ 10.2 kg·cm.

Step 3: speed in RPM

RPM = v ÷ (2π × r) × 60

Step 4: add a margin

Real motors lose speed as they work harder, gearboxes waste energy, and your robot will gain weight. Multiply the torque by 2 and choose a motor whose rated (or "operating") torque meets that number. If the seller only lists stall torque, choose a motor whose stall torque is at least 3–4 times your required torque: motors run hot and inefficiently near stall.

For speed, pick a motor whose no-load RPM is about 25–50 % higher than the RPM you calculated, since it slows down under load.

Worked example

A small two-wheel robot:

  • Mass: 1.5 kg
  • Wheels: 65 mm diameter → r = 0.0325 m
  • Top speed: 0.5 m/s
  • Slope: 10° (a gentle ramp or a door threshold)
  • Acceleration: 0.5 m/s²
  • Crr: 0.03
  • Driven wheels: 2

Force: - Slope: 9.81 × sin 10° ≈ 1.70 - Rolling: 0.03 × 9.81 × cos 10° ≈ 0.29 - Acceleration: 0.5 - Total: 1.5 × (1.70 + 0.29 + 0.5) ≈ 3.7 N

Torque per motor: 3.7 × 0.0325 ÷ 2 ≈ 0.060 N·m ≈ 0.61 kg·cm With a ×2 margin: about 1.2 kg·cm operating torque per motor.

Speed: 0.5 ÷ (2π × 0.0325) × 60 ≈ 147 RPM → look for about 180–220 RPM no-load.

Power check: mechanical power = F × v ≈ 3.7 × 0.5 ≈ 1.9 W total. Small gear motors are roughly 40–60 % efficient, so expect about 4 W from the battery while climbing at full speed, a useful number for choosing a battery.

What the numbers tell you

  • The slope term is often the biggest. A robot that only drives on flat floors needs far less torque; if 10° is not realistic for your robot, redo the math with 0°.
  • Bigger wheels need more torque but less RPM. Halving the wheel diameter halves the torque but doubles the RPM needed.
  • Weight multiplies everything. Lighter batteries and chassis pay off twice.

Typical motor choices

Motor Typical use
Yellow "TT" gear motors (1:48) Light robots under ~1 kg on flat floors; cheap but low torque and uneven
N20 micro metal gear motors Small, light robots; many ratios available, often with encoders
25 mm / 37 mm metal gear motors 1–5 kg robots, slopes and carpet; strong and durable

Check the voltage the seller's figures are measured at; the same motor at 6 V and 12 V has very different speed.

Don't forget the driver

The motor's stall current decides the driver. A driver that can't handle the stall current will overheat every time the robot bumps into a wall. Compare motor currents against the limits in L298N vs TB6612. The chassis layout and wheel choices are covered in the robot chassis guide.

Quick recap

  1. Force = mass × (slope + rolling + acceleration).
  2. Torque per motor = force × wheel radius ÷ driven wheels.
  3. RPM = speed ÷ wheel circumference × 60.
  4. Double the torque, add 25–50 % to the RPM, and choose the motor and driver from there.

— TheSolderBench · found a mistake? tell me

More pages from this notebook

How a Line-Following Robot Works

The sensors, logic and code behind a line follower, from a simple two-sensor bang-bang robot to smoother proportional steering.

→ wobbling? lower the gain

PID Control Explained Without Heavy Math

What the P, I and D terms actually do, shown with a robot that follows a line, plus Arduino code and a step-by-step tuning method.

→ tune P first, then D, I last

Choosing a Chassis for Your First Robot

Two-wheel, four-wheel, tracked or DIY? Compare robot chassis types by steering, terrain and difficulty, and learn how to check motor and battery fit.

→ pick the battery before the chassis

Adding Wheel Encoders to a Robot

How optical and magnetic encoders count wheel rotation, how to read them with interrupts, and how to measure distance and drive straight.

→ count in an interrupt, not in loop()